Waves in-ice observations made during the SIPEX II voyage of the Aurora Australis, 2012
Published by Australian Ocean Data Network
About this dataset
Antarctic sea-ice is highly influenced by the dynamic nature of the Southern Ocean. Ocean waves can propagate from tens to hundreds of kilometres into sea-ice, leaving behind a wake of broken ice sheets. As global climate change intensifies, storm intensity will increase in the Southern Ocean. Increased storm intensity will bring stronger winds and bigger waves, which has the potential for waves to travel deeper into the ice pack and increase the likelihood that ice floes break apart. To enhance our understanding of this system, our aim during SIPEXII was to improve on the scarce Antarctic waves-in-ice dataset by collecting a set of wave observations in the MIZ. In order to achieve this, we designed and produced eight custom made wave sensors. The sensors were deployed in the Antarctic marginal ice zone along a transect line perpendicular to the ice edge and spread over approximately 200 km. Every three hours, the sensors simultaneously woke and recorded their location and a burst of wave acceleration data. Each sensor performed on-board data quality control and spectral analysis before returning the wave spectrum via satellite. The sensors were powered via lithium batteries and had enough battery power to last a minimum of 6 weeks. This project involved collaboration between the Australian Antarctic Division (AAD) and the NZ's National Institute for Water and Atmospheric Research (NIWA). The work was funded by a New Zealand Foundation of Research Science and Technology Postdoctoral award to A.L.K.; the Marsden Fund Council, administered by the Royal Society of New Zealand; NIWA, through core funding under the National Climate Centre Climate Systems programme; the Antarctic Climate and Ecosystems Cooperative Research Centre; and Australian Antarctic Science project 4073. Instruments were designed and built by Inprod PTY LTD. Below is a summary of the design and hardware: Accelerometer: Kistler ServoK-Beam accelerometer. Model 8330B3. IMU: Razor IMU (3 axis acceleration, 3 axis magnetometer and 3 axis gyro) ADC: TI ADS1247 Analog-to- Digital converter CPU (main): Arduino Mega 3.3V CPU (maths): BeagleBone from BeagleBoard.org who use Texas Instruments (TI) ARM processors GPS: Skytraq Venus634FLP Temperature readings: SHT15 from SparkFun Transmission: Iridium 9602 Battery: Lithium batteries (enough to survive a minimum of 6 weeks) Inner housing: Explorer 1908OE Outer housing: The case is fitted in a fork lift tyre ( .53 m diameter and .165 m height) with an inner tube to enable floating. Aerial housing: The aerial is housed in a plastic spherical container on top of a .5 m tube attached to the tyre. Feet: 3 screws stick out of the bottom to create friction with the ice. Onboard processing: Every 3 hours, the instruments wake and record wave accelerations for 35 mins. An initial low pass analogue filter is used. We over sample at 64 Hz and decimate down to 2 Hz. Downsampling from 64 Hz to 2 Hz is achieved through a multistage decimation of 8 followed by 4, to achieve a total decimation of 32. Prior to each downsampling stage, a second order lowpass Butterworth filter is applied to remove all components above the nyquist frequency. We first apply the Butterworth filter with a cut off of 1 Hz and sample at 8 Hz and secondly with a cut off of 0.5 Hz and sample at 2 Hz. A high-pass filter was then applied and the acceleration double-integrated to provide displacement. Welch's method, using a 10% cosine window and de-trending on four segments with 50% overlap, was applied to estimate the power spectral density. Sample frequency: 2 Hz Sample duration - raw: 2048 sec Sample duration - fft: 1280 sec No. of discrete bins of fft: 512 No. of segments: 4 Below is a detailed description of each line of the raw output. Header info L1: Longitude (decimal degrees) L2: File name of attachment emailed via Iridium L3: Temperature inside the box (degrees Celsius) L4: Sensor identification number L5: Time wave record starts (24 hr format HHMMSS) L6: D